Skip To Content

Configuring event replacement

While performing roadway maintenance, sometimes a road section is replaced by a new section.

During the roadway replacement, the events that were part of the replaced section can be left as is, retired, or retired and replaced using the Event Replacement widget. The measures for the route do not change. For example, the following diagram illustrates a roadway section before replacement

Roadway before replacement

Roadway before replacement

Table 1: Event table before replacement

Event layerEvent IDFrom measureTo measureValueFrom dateTo date

Event 1

1A

1

GGG

1/1/2000

Null

Event 2

2A

2

SSS

1/1/2000

Null

Event 3

3A

3

HHH

1/1/2000

Null

Event 4

4A

0

10

XXX

1/1/2000

Null

Event 5

5A

0

10

YYY

1/1/2000

Null

Event 6

6A

0

10

ZZZ

1/1/2000

Null

Event 7

7A

0

10

QQQ

1/1/2000

Null

Event 8

8A

0

10

WWW

1/1/2000

Null

A road with a From measure of 0 and a To measure of 10 exists. Various line and point events are present on the road as shown above.

During inspection, it was deduced that a section of the road between the measures 0 and 5 needs to be replaced on 12/31/2017, as shown below.

Section of the road to be replaced

Section of the road to be replaced

The events are placed in the following event replacement categories:

Table 2: Event replacement categories

RetireRetire and replaceKeep as is

Event 2

Event 5

Event 1

Event 3

Event 8

Event 7

Event 4

Event 6

The results of replacing the road section and replacing the events are shown in Table 3.

Event replacement on roadway

Event replacement on roadway

Table 3: After event replacement

Event layerEvent IDFrom measureTo measureValueFrom dateTo dateCase

Event 1

1A

1

GGG

1/1/2000

Null

A

Event 2

2A

2

SSS

1/1/2000

12/31/2017

B

Event 3

3A

3

HHH

1/1/2000

12/31/2017

C

Event 4

4A

0

10

XXX

1/1/2000

12/31/2017

D

Event 4

4B

5

10

XXX

1/1/2000

Null

E

Event 5

5A

0

10

YYY

1/1/2000

12/31/2017

F

Event 5

5B

5

10

YYY

1/1/2000

Null

G

Event 5

5C

0

5

YYYOO

12/31/2017

Null

H

Event 6

6A

0

10

ZZZ

1/1/2000

12/31/2017

I

Event 6

6B

5

10

ZZZ

1/1/2000

Null

J

Event 7

7A

0

10

QQQ

1/1/2000

Null

K

Event 8

8A

0

10

WWW

1/1/2000

12/31/2017

L

Event 8

8B

5

10

WWW

1/1/2000

Null

M

Event 8

8C

0

5

WWWOO

12/31/2017

Null

N

Table 4: Explanation of event replacement

CaseEvent layerExplanation

A

Event 1

The event is left as is.

B

Event 2

The event is retired because it was in the retire category.

C

Event 3

The event is retired because it was in the retire category.

D

Event 4

The whole event is retired because it was in the retire category.

E

Event 4

A new event is created for the existing section of the road, keeping the dates and attribute values of the old event.

F

Event 5

The whole event is retired because it was in the retire and replace category.

G

Event 5

A new event is created for the existing section of the road, keeping the dates and attributes of the old event.

H

Event 5

A new event is created for the new section of the road with the new dates and attributes provided in the Event Replacement widget.

I

Event 6

The whole event is retired because it was in the retire category.

J

Event 6

A new event is created for the existing section of the road, keeping the dates and attribute values of the old event.

K

Event 7

The event is left as is.

L

Event 8

The whole event is retired because it was in the retire and replace category.

M

Event 8

A new event is created for the existing section of the road, keeping the dates and attribute values of the old event.

N

Event 8

A new event is created for the new section of the road with the new dates and attributes provided in the Event Replacement widget.

The workflow for event replacement in Event Editor involves the following two stages:

  • Configuring event replacement using the Configure Event Replacement widget
  • Replacing events using the Event Replacement widget

The configuration of event replacement requires categorizing the events in the map service into three categories: As Is, Retire, and Retire and Replace.

To configure event replacement, complete the following steps:

  1. Open Event Editor and, if prompted, sign in to Portal for ArcGIS or ArcGIS Online.
  2. Click the Edit tab.
  3. In the Edit Events group, click the Configure Event Replacement button Configure Event Replacement.

    The Configure Event Replacement widget appears.

    Note:

    All the line events Line Events and point events Point Events available in the map service are listed in the Available Event Layers list.

    Opening the Configure Event Replacement widget

    Opening the Configure Event Replacement widget

    Tip:

    If a default configuration has been created, click Default to load it. Click Reset to return to the last saved configuration in the map service.

  4. Click Shift or Ctrl and click and drag multiple line events from the Available Event Layers list to the Retire Events list.

    Choosing events for retirement

    Choosing events for retirement

    You can also choose event categories and use the arrow keys to move selected line events into the lists from left to right or up and down between the Retire Events and Retire and Replace Events lists.

    Events placed in the Retire Events list will be retired when events in the category are replaced using the Event Replacement widget.

    Choosing events for retirement and replacement

    Choosing events for retirement and replacement

  5. Click Shift or Ctrl and click and drag multiple line events from the Available Event Layers list to the Retire and Replace Events list.
    Note:

    Only line events Line Events can be retired and replaced.

    Event replacement configured

    Event replacement configured

    Note:

    Event layers left in the Available Event Layers list are left as is. If no events are configured to retire or to retire and replace, you'll be unable to save using the Event Replacement widget.

  6. Optionally click the arrow for any event layer in the Retire and Replace Events list to expand it.

    An expanded list of fields in the event layer appears.

    Expanded event layer fields

    Expanded event layer fields

    You can use these check boxes to show or hide the fields when performing the event replacement operation.

    Note:

    Some attribute fields are required fields, which is denoted by the asterisk (*) symbol. A required field is a nonnullable field with no default value. Visibility can't be changed for required fields.

  7. Click Save to save the event replacement configuration.
  8. Click Export to export the configuration to an LRER file. Give the configuration file a name such as eventplacement1.lrer.
    Note:

    The event replacement configuration is saved in the local browser’s download folder.

  9. Copy the exported file to the Event Editor folder.
  10. Open the configuration file (config.json) in a text editor such as Notepad.
  11. Type the LRER file name with the file extension in the eventReplacement section:
    eventReplacement section of config.json
    Note:

    The Default button defaults to the event replacement configuration provided in the Event Editor configuration file.

    The Reset button restores the last saved event replacement configuration for that browser.

    You can edit the default event replacement configuration and use it in your browser.

Related topics


In this topic